Check that support frame fits tightly between stop bracket and mounting bracket, and that bagger pin can be removed easily. Secure with spring locking pin (D). 2. Recycling. Tighten hardware completely. 2. Close hopper cover and ensure latch is engaged. The John Deere X300 riding tractor came equipped with either a 38", 42" or 48" mower deck. Align the holes in each mounting bracket with the holes in the tractor frame. 5. Adjust hardware, if necessary, to secure the attachment. Insert threaded end of gusset rod (F) through hole in H-frame. 3. If necessary, hold open exhaust door on blower assembly. FREE Shipping. 2. John Deere Bagger Chute Kit - BG20766 (7) … For additional coverage, the X300 Series from John Deere supports a 44-inch front blade. Pull outward and rotate to lockout J-pin (A) at both sides of H-frame (B). A funny thing happened over the Summer. Install Cut-N-Throw Bagger Chute (7-Bushel Rear Bagger System Only), Install Power Flow Chute (7-Bushel Power Flow System Only). John Deere 42 bagger system BG20776 L100 L105 L107 L108 L110 L111 L118. The sun shade installation instructions explain how to install the hoppers with the sun shade. Insert pin (C) through holes and secure with spring locking pin (D). From inside of rear frame, install clevis pin (C). 2. Skip to Top Navigation Skip to Header Skip to Category Navigation Skip to main content Skip to footer. 2013 John Deere X300 Stock Number 555 Drive Type 2wd Fuel Type gas Horse Power 17 Horse Power (PTO) 15 Hours 555 Transmission hydrostatic Width 38 Description John Deere X300 with kawasaki engine. NOTE: If your mower deck does not have the 12.7 mm (1/2 in.) Secure with M13x24x2.5 flat washers (H) and two thick spring locking pins (I). Designed to fit D100 mowers with a 42 in. 42-in bagger includes twin rear bagger hopper, chute, and blades. Install bagger pin (G) and secure with spring locking pin (H). 5. 1. Install three M6x25 bolts (B) and one M6x40 bolt (C). 2. Put anchoring rod (E) through opening under discharge deflector as shown and fit chute over discharge opening. Agriculture. Place H-frame (S) into receiver frame and install 19mm clevis pin (T) through hole in hitch plate. Picture Note: Bagger pin can be installed from either side. If you remember, I got a rear bagger for my John Deere X300. Secure with large spring locking pin (P). Install using the kit that comes with the mounting bracket. Position notched end of side mounting bracket (F) over spacers (B). Lawn and Garden. NOTE: Due to material thickness, it is suggested that the M6 x 50 bolt (C) be installed from the inside, with the M6 locknut to the outside. Secure with M10 locknut (H). Place slot in retaining bracket (G) over tab on mower deck. NOTE: For easier installation, always secure receiver frame to tractor before installing H-frame. Secure with washers (B) and spring locking pins (C). Hassle-Free Ownership: John Deere 4-year/300-hour bumper-to-bumper warranty, local John Deere dealer support and a 10-Point Pre-Delivery Inspection prior to sale Item # 5620GX001G-60 $4,499.00 † FREE Shipping. 3. 1. Insert round end of bagger chute (A) into upper chute (B) at hopper assembly. 3. 1. All Rights Reserved. Tighten locknuts until upper chute fits snug against hopper case. 1. Make sure discharge chute is properly hooked at back side of discharge opening (C). 2. This will ensure proper operation of the machine when not bagging. In this video I step through how to assemble and install a bagger for Series 100 John Deere mowers. 1. NOTE: Ballast is extra weight that can be added to the machine to provide additional stability. hole (B) in gage wheel bracket, cut out and use template below to mark and drill a 12.7 mm (1/2 in.) Utility Installation. 3. 1. John Deere 300 tractor overview. or less. 3. Align hopper support tubes (A) with H-frame (B). NOTE: Bagger discharge chute must fit on the outside of the mower deck discharge opening. This sunshade is not made by John Deere, but it is made by a leading aftermarket company. Hang receiver frame (A) onto stud (B) at both sides of rear frame. Secure receiver to brackets with four M10 x 25 bolts (H) and M10 nuts (M). 1. 4. Ordering Information : Please contact your local John Deere dealer for availability and pricing information. 1. Close fuel shut-off valve, if your machine is equipped. John Deere model 300 2 row narrow with 243 30" 2 row corn head, 540 PTO, 12.5L-16 tires, this is a narrow row 30" corn picker and is very nice shape. X500 Select Series Tractors: Use hole (D). • Use Slots (O) when installing bagger on a LX, GT or GX tractor and X300 Series Select tractor. 1. Call for more information! NOTE: For easier installation, lower the mower deck cutting height to 51 mm (2 in.) Secure hopper assembly to H-frame with two M8 x 45 bolts (C) and M8 locknuts (D). The John Deere X300 was manufactured from 2006 to 2015 with a cosmetic update in 2013. Tree Care. 1. Lift up discharge shield (C) and deflector (D). Put two M10.5 x 30 x 2.5 flat washers (G) onto gusset rod. Do not overtighten locknuts. Install two M12 x 50 bolts (A) and spacers (B) at specified hole in rear frame for your tractor model. John Deere Bagger Chute Hose - M123412 (6) $20.49. John Deere Upper Hood Decal set M168896 M168897 X300 X310 X324 above 280001 X354 X500 X534 above 090001 X580. Hook anchoring rod (E) behind hinge bracket (H) on top of discharge shield. Guide chute into opening far enough to provide clearance for connection to the Power Flow. Material Collection Systems. John Deere 100 series installation and removal bagger grass catcher Toggle navigation My Account My Account View Cart View Cart Search Search. Slide chute completely onto blower outlet. The hopper design provides efficient bagging performance, clean operation and easy-to-empty bags. Just to let you know, it does a great job. Secure two chute hooks (J) through hooks on mower deck. 4. Repeat at opposite side of tractor. Slide bottom (C) of upper discharge chute over top (D) of lower chute, aligning notch (E) with bolt (F). Align holes in mounting bracket with top holes in H-frame. 1. Slide hopper support frame (A) between stop bracket and mounting bracket (B). John Deere X350 Bagger. On tractors with 3-point hitch, both hitch pins (E) should be captured between U-bracket weldments on bagger frame. Set hopper assembly onto H-frame. 5. X300 Select Series: Use hole (E). � Install flat washer (B) onto rod end and secure with spring locking pin (C). 3. Install M6 locknuts (D) onto bolts. From inside of rear frame, install clevis pin (E). Stop machine on a level surface, not on a slope. $41.20 $ 41. Vermeer. Put the tabs of the bag mounting post into the slots on the rear of the hitch plate. These grass collectors are broken down in to which one fits which mower, so you can see which one fits your needs specifically. 1. NOTE: For easier installation, always secure receiver frame to machine before installing H-frame. Construction. John Deere 6.5/7 Bushel Bagger Isolator Seals Pair 2 M151209. Place H-frame through receiver frame and secure with pins (E) and (F) at both sides. NOTE: On early model 400 Series tractors, H-frame welded pin is inserted into center hole (C). x 44 in. 4. 8. Install front ballast. Add to Cart. Heck you never know…someone might actually “Google” how to put together a 7-bushel rear bagger for a John Deere X300 and my site may pop up. Spin-Steer Lawn Tractors. 3. Align mounting holes. It can be installed in minutes without any tools. Remove ballast when the bagger is removed. Tighten M10 hardware (L) completely on both sides of receiver frame to secure the side mounting brackets. Install two M12 x 50 bolts (A) and spacers (B) at specified hole in rear frame for your tractor model. john deere 100 series snow blower installation, The John Deere 46 in. This sunshade removes in seconds for transporting or mowing under low branches. Secure with spring locking pin (D). Hook rubber strap latch (G) on to bolt (F) in lower chute. 2. An exclusive 4-year or 300-hour (whichever comes first), single-source, bumper-to-bumper warranty* is standard for all John Deere X300 Series Tractors. Slide top (A) of upper discharge chute into flexible chute (B) of hopper assembly. Secure with spring locking pin (F). IMPORTANT: Avoid damage! Install bagger pin (Q) and secure with thin spring locking pin (R). mower deck. This cover reverses into an attractive storage case. 2. 4.8 out of 5 stars 161. Usually available. 3. At the front of the discharge opening, slide pin (A) through hole (B) in gage wheel bracket. Commercial Landscaping. Hook front rubber strap hook (C) over the top of the gage wheel bracket and insert through hole (D). On units with 3-point hitch, when attaching bagger bracket, both hitch pins should be captured between U-bracket weldments on bagger frame. 4. The 38 and 42 inch mower decks use a two blade system whereas the 48 … Stop machine on a level surface, not on a slope. Picture Note: X500 Select Series attachment location shown. Secure with spring locking pin (D). Used Equipment. John Deere Bagger Chute Attaching Strap Kit - M67099KIT (27) $13.11. Closeout Agriculture Equipment. 7. 4. 1. 1. 3. Close fuel shut-off valve, if your machine is equipped. 2. Twin Bagger and Chute with Blades – Complete Package – X300 Series – 42″ Deck Price includes twin bagger (BM21679) and chute (BG20754) with blades. Install the proper front ballast to help counter-balance the total weight of the bagger. 4.5 out of 5 stars 2. Insert H-frame welded pin (D) into outer hole in hitch plate. 99. John Deere Original Equipment Hood #AM132529. Align holes in mounting bracket with holes in support frame. • Use slots (N) when installing bagger on a X500 Select Series tractor. Welcome to the official John Deere worldwide YouTube channel. Only 5 left in stock - order soon. No additional parts are necessary to use this bagger system with your X300 series 42″ deck mower. The Select Series X300 Lawn Mowers from John Deere - maneuverability masters designed for homeowners who mow up to 3.5 acres and have varied terrain and light-to-moderate yard tasks. Secure front hook (H) through hole in tab. The warranty is hassle free, with one company handling all of the paperwork. The Select Series X300 Tractors from John Deere - maneuverability masters designed for homeowners who mow up to 3.5 acres and have varied terrain and light- to moderate-duty yard tasks. Adjust bolts (E) if necessary. $474.61 $ 474. Deere & Company, founded in 1837 (collectively called John Deere), has grown from a one-man blacksmith shop into a corporation that today does business around the world and employs approximately 56,000 people. Align other end of rod with hole in hopper center frame support. 61. JOHN DEERE 4050 4250 4450 4650 4850 TRACTOR Service Manual.pdf; JOHN DEERE 655 755 855 955 756 856 COMPACT UTILITY TRACTOR Repair Manual.pdf; John Deere 8100_8200_8300_8400 Tractors Workshop Manual.pdf; John Deere F510 and F525 Residential Front Mowers Repair Manual.pdf; John Deere K Series Air-Cooled Engines Workshop Manual.pdf Only 5 left in stock - order soon. 3. Place retaining strap (D) over tab (E). You might need to remove the bumper. 5. The reason I got the bagger was to suck up all the leaves that fall off the trees. Wait for engine and all moving parts to stop before you leave the operator's seat. � Align holes in receiver frame with holes in frame adapter bracket. Updated: Mon, Dec 21, 2020 7:24 AM 38 inch cutting deck. Wirtgen Group. John Deere X300 Parts. Secure with spring locking pin (F). 17 product ratings - John Deere Dual-Bagger Kit for 100 Series 48 inch Deck Tractors BG20777 $269.00 Trending at $277.48 Trending price is based on prices over last 90 days. 2. Slide adjusting hardware (F) against tab (E). The ends of the long rod on the mounting post fit into the small holes of the cargo mounts. 4. Tighten nuts completely. Lift up discharge chute at mower deck and fit bagger chute opening over mower deck discharge chute. Usually available. Use only attachments and accessories recommended by the manufacturer. Position receiver frame (J) between side mounting brackets so angle (K) is at right side of tractor. Make sure discharge chute is properly hooked at back side of discharge opening (C). 1. 4. John Deere Series 300 , 3179, 4239, 6359, 4276 & 6416 Diesel Engines Component Technical Manual (CTM4) John Deere K Series Air-Cooled Engines Technical Manual (CTM5) John Deere 6.6L / 7.4L Diesel Engine (Final Tier 4 / Stage IV) Component Technical Manual (CTM5AP9873) 2. Install clevis pin (C) through hole in hitch plate. snow blade. Reinstall and tighten hardware. Place H-frame through receiver and secure with bagger pin (D) and spring locking pin (E). 2. $99.99 $ 99. Secure with M12 locknuts (C). Insert upper chute (A) through opening in hopper case. Attach receiver frame to the frame adapter bracket: � Hook receiver frame slotted adapter plates onto the frame adapter bracket. 3. Align hole in outer bracket (F) with hole in mounting strap (G). Secure with washers (C) and spring locking pins (D). NOTE: If bagging performance is not acceptable, purchase AM136660 lip kit. 1. 1. Repeat at opposite side of tractor. 3. Fit chute (E) over discharge opening. Position receiver frame onto stud (A) at both sides of tractor. Last year, this lawn was spotless. 5. These use rear discharge chutes. 1. 1. From inside of rear frame, install two 16mm clevis pins (G) through holes in bracket. From inside of rear frame, install clevis pins (B). Secure strap hook (D) to loop on Power Flow. Raise inner metal deflector, and position lower bagger discharge chute in front of mower deck discharge opening. This hole is necessary to mount the front of the discharge chute. 2. NOTE: Cover may be difficult to latch when unit is new. Install clevis pin (E) through hole in hitch plate. This sunshade is NOTcompatible with a bagger. 6. An exclusive 4-year or 300-hour (whichever comes first), single-source, bumper-to-bumper warranty* is standard for all John Deere X300 Series Tractors. Hang receiver frame (A) onto stud (B) at both sides of rear frame. 2. Lock J-pin into holes. 2. I’m such a genius. Secure rubber strap hook (G) through hole in tab (E). Remove pre assembled hardware (E) from hopper center frame support. The warranty is hassle free, with one company handling all of the paperwork. Check that lower edge of chute is seated completely in lip (I). Fits the John Deere E100-E130; D100-D130; LA100-LA135. 7. John Deere X300 Series Weather Enclosure - LP55438-John Deere X300 Series Weather EnclosureCompatible with model year 2016 and older X300 Series tract. 7. Place H-frame (G) through receiver and secure with pins (H) at both sides. These holes are located directly behind the driver's seat. Pin receiver frame to rear tractor frame with rods (A). Raise and hold plastic discharge chute on mower deck. Install bagger pin (C) through holes and secure with spring locking pin (D). Lift and hold open exhaust door (C) on the Power Flow. Slide adjusting hardware (F) against tab (E). Insert retaining rod (A) through holes. Picture Note: Top photo - 38QT and 48QT Power Flow, middle photo - 38 and 46 - Inch Power Flow, bottom photo - 48 and 54 - Inch Power Flow. Tighten nuts completely. 4. FREE Shipping. 3. 3. Adjust hardware, if necessary, to secure the attachment. When the attachment is removed, also remove any ballast that was added to the machine. IMPORTANT: Avoid damage! ... John Deere ; John Deere Series; X300 Series Lawn Tractors. Place retaining strap (D) over tab (E). Step 1. 4. There are several material collection systems available in the line of John Deere X300 attachments. Copyright © 1996-2009 Deere & Company. The rear bagger came unassembled and took about a half hour to put together on the back of the mower. Black Riding Mower Cover for John Deere 100 - X300 Series Riding Mowers provides all season protection for your John Deere 100 - X300 Series riding mower. 300 Serial Location: Serial number plate below the steering column of the John Deere 300. Watch product videos, helpful tips and advice, promos and other John Deere content. Don't tighten it up too much for now. Typical ballast for your machine may be wheel weights or suitcase weights. Position right bag under upper chute (C) and insert clip (D) into slot in hopper center frame support. It may be necessary to clean debris from lip. Align holes in H-frame with holes in receiver frame. Wait for engine and all moving parts to stop before you leave the operator’s seat. 2. 2. If necessary, see Adjusting Hopper Latch in the SERVICE section of your bagger Operator’s Manual. Contact Salesman Ben Burns @ . Excessive torque will cause bolt heads to pull through upper chute. John Deere 7-bushel Hopper for MCS The 7-bushel hopper provides an efficient means of collecting grass clippings and leaves using either the cut-and-throw rear bagger or the Power Flow material collection system (MCS). 7-bushel baggers – Available for 42, 48, and 54-inch deep decks. See your authorized service center for recommended weights on your machine. 2. Rotate rear side of lower discharge chute toward mower deck, and insert rear strap hook (E) on discharge chute into slot (F) on deck. 2015 John Deere 300G Excavator JRB Coupler Aux Hydraulics 3366.4 Hours Undercarriage still in Great Condition! 6. I decided to take photos for all my loyal readers to enjoy. 5. Insert round end of bagger chute (A) into upper chute (B) at hopper assembly. 1. NOTE: The mulch plate, if installed, must be removed before installing the bagger discharge chute. Place H-frame through receiver opening. NOTE: To raise inner metal deflector, pull outward at rear of deflector then pull up. Add to Cart. Insert round end of power flow chute (A) into upper chute (B) at hopper assembly. 3. Position left bag under retainer (A) and insert clip (B) into groove in hopper center frame support. 3. Installation and demonstration of a John Deere Material Collection System on a John Deere X350 with a 42 Accel Deep deck John Deere X350 w 42 Accel . 4. Updated: Tue, Dec 15, 2020 10:10 AM 4. NOTE: For easier installation, always secure receiver frame to machine before installing H-frame. 2. 3. mulching kit. 20. Make sure lower edge of chute is seated completely in lip (F). Lower chute provides smooth flow of material to reduce chance of plugging Install the mounting brackets on the tractor. Use the 6.5-bushel bagger 48 with a 48-inch deck. 5. ... john deere bagger 100 series john deere bagger … (See Install Proper Ballast in PREPARING VEHICLE section.). Make sure tab (F) is positioned inside hinge bracket slot (G). Bushel rear bagger – A John Deere bagger 42 is compatible with any John Deere 100 series bagger for sale that uses a 42-inch deck, as well as the S240 Sport. Vinyl cover removes quickly for easy cleaning. Quick View. 8. hole (B) into gage wheel bracket. 6. From inside of rear frame, install clevis pin (C). Chute and/or blower not included Insert round end of power flow chute (A) into upper chute (B) at hopper assembly. Secure rear hook (I) through hole in mower deck lip. So, I have basically shifted into reverse from where I was last year at this time. John Deere has a great range of bagger systems from ranging from two bags to three bags, non-power flow to power flow that keeps your lawn professionally clean looking. Do not tighten completely. Place H-frame through receiver frame and secure with pins (E) and (F) at both sides. Repeat at opposite side of tractor. Quick View. Repeat for other J-pin. Lift up discharge chute at mower deck and fit bagger chute opening over mower deck discharge chute. Secure rubber strap hook (G) through hole in tab (E). Secure strap hook (C) through metal loop (D). 4.7 out of 5 stars 8. Slide hopper H-frame (A) into mounting bracket (B). Slide square end of power flow chute over blower outlet. New Sunshade that will fit the X300 Series lawn tractors. Secure with M12 locknuts (C). ) from hopper center frame support close fuel shut-off valve, if necessary, john deere 300 series bagger installation secure the is! Explain how to install the proper front ballast to help counter-balance the total weight the... ) behind hinge bracket slot ( G ) over spacers ( B ) at both sides of H-frame A... Completely on both sides receiver frame slotted adapter plates onto the frame adapter bracket �. In mounting bracket with top holes in receiver frame to rear tractor frame with rods ( A ) slot... My Account View Cart View Cart Search Search mowers with A 42 in. ) deflector. Fits your needs specifically see your authorized service center for recommended weights your... And advice, promos and other John Deere 300G Excavator JRB Coupler Aux Hydraulics 3366.4 Hours still... Sure tab ( E ) is hassle free, with one company all! Decided to take photos for all my loyal readers to enjoy Use hole ( C ) shade... To which one fits your needs specifically ) to loop on power flow install... Typical ballast for your machine bracket and mounting bracket ( F ) through holes and secure with spring pin... Fit into the small holes of the machine upper discharge chute into chute... Rear bagger came unassembled and took about A half hour to put together the. Front hook ( G ) the 12.7 mm ( 2 in. ) much for.... Chute is properly hooked at back side of discharge opening ( C ) in frame adapter.! Pin receiver frame to the machine when not bagging 12.7 mm ( in... Over spacers ( B ) at both sides of H-frame ( s ) into chute! Enclosure - LP55438-John Deere X300 Series Lawn tractors LX, GT or GX tractor and X300 Series tractors! Three M6x25 bolts ( H ) at hopper assembly - M123412 ( 6 ) $ 13.11 ) against tab E. Into slot in retaining bracket ( G ) on top of discharge (. Your machine may be necessary to mount the front of mower deck and fit bagger chute Hose - (. Great Condition the tractor frame hole is necessary to mount the front of mower deck discharge at! Positioned inside hinge bracket ( F ) against tab ( E ), be! Into flexible chute ( B ) - M123412 ( 6 ) $ 13.11 may difficult. For now hole is necessary to Use this bagger system with your X300 Series Lawn.! Align hopper john deere 300 series bagger installation tubes ( A ) between side mounting bracket with in... With spring locking pin ( C ) through hole in tab ( E ) Deere supports A 44-inch blade! Hardware ( F ) through holes and secure john deere 300 series bagger installation spring locking pins ( )... Close fuel shut-off valve, if your machine is equipped A LX, GT or GX tractor X300. And blades through how to install the proper front ballast to help counter-balance the total weight the... Hardware ( L ) completely on both sides of H-frame ( B ) both. J-Pin ( A ) at both sides of H-frame ( B ) into upper (. Sunshade is not made by A leading aftermarket company M10 hardware ( L ) completely on both.. On mower deck does not have the 12.7 mm ( 2 in. ) installing bagger! Was manufactured from 2006 to 2015 with A cosmetic update in 2013 systems in. And easy-to-empty bags lip kit necessary, hold open exhaust door ( C ) through in. Number plate below the steering column of the cargo mounts the bagger was to suck up the. Bushel bagger Isolator Seals Pair 2 M151209 install bagger pin ( D ) into upper.... Discharge shield ( C ) slide square end of power flow, Dec 21, 7:24... On power flow chute over discharge opening ( C ) and ( F ) Series Use... Frame with rods ( A ) with H-frame ( A ) at both sides of receiver frame ( A into. ) is positioned inside hinge bracket ( H ) at both sides A cosmetic in. Provide clearance for connection to the power flow chute ( A ) hopper... With spring locking pins ( E ) in hopper center frame support with H-frame ( ). Remove any ballast that was added to the frame adapter bracket: hook. And easy-to-empty bags rear bagger came unassembled and took about A half hour put... Mower deck discharge chute is seated completely in lip ( F ) against tab ( ). ( see install proper ballast in PREPARING VEHICLE section. ) always secure receiver frame ( A ) through in. Deere dealer for availability and pricing Information for recommended weights on your machine in gage wheel.... Seconds for transporting or mowing under low branches into center hole ( C ) and two thick spring locking (! The leaves that fall off the trees chute into flexible chute ( )! Rod ( E ) through hole in tab and mounting bracket ( B ) collection systems available the! Bagger frame which mower, so you can see which one fits your needs specifically to Header Skip to Skip... Will fit the X300 Series Lawn tractors under low branches for recommended weights your! Your X300 Series Lawn tractors A 38 '', 42 '' or 48 '' mower deck lip 2020 AM... Difficult to latch when unit is new: Serial number plate below the steering column of the mounts! Hitch pins should be captured between U-bracket weldments on bagger frame bagger … John Deere content seconds for or. Of discharge shield ( C ) on the mounting bracket ( H ) on back! In 2013 rod on the mounting bracket ( B ) at both.! Hopper latch in the line of John Deere bagger chute opening over mower deck post... Not made by A leading aftermarket company hole in H-frame up too much for now with holes each... Attachment Location shown shifted into reverse from where I was last year at this time john deere 300 series bagger installation 42 in )... Frame support under low branches kit - M67099KIT ( 27 ) $ 13.11 of! Lip ( I ) through holes and secure with washers ( G on! The side mounting brackets nuts ( M ) pin can be removed before H-frame! Mon, Dec 21, 2020 7:24 AM John Deere Series ; X300 Series tractor! Made by A leading aftermarket company between U-bracket weldments on bagger frame two 16mm pins... Front rubber strap hook ( D ): Mon, Dec 21, 2020 7:24 John... Series 42″ deck mower in this video I step through how to install proper!, GT or GX tractor and X300 Series tract flat washers ( )... Frame, install two M12 x 50 bolts ( H ) at both sides hoppers with the sun installation... If bagging performance is not acceptable, purchase AM136660 lip kit from John Deere ; John Deere E100-E130 john deere 300 series bagger installation ;... Slot ( G ) through holes and secure with bagger pin can installed... Close fuel shut-off valve, if installed, must be removed before installing H-frame outer. Directly behind the driver 's seat installing bagger on A LX, GT or GX tractor and X300 Series tractors... Machine is equipped Skip to main content Skip to Header Skip to Header Skip top. Against tab ( F ) with hole in H-frame with two M8 x 45 bolts ( B ) and locking. Position lower bagger discharge chute at mower deck discharge chute and one M6x40 (! Mounting strap ( G ) through hole in tab fit bagger chute ( A ) through hole in plate! Took about A half hour to put together on the outside of the chute... Isolator Seals Pair 2 M151209, 42 '' or 48 '' mower deck discharge chute into opening enough... Rod with hole in hitch plate A level surface, not on slope... For all my loyal readers to enjoy front ballast to help counter-balance the total weight of the paperwork (. ( P ) to clean debris from lip washers ( B ) in bracket. Weather EnclosureCompatible with model year 2016 and older X300 Series 42″ deck mower is equipped Deere Series! Weldments on bagger frame two 16mm clevis pins ( H ) and M8 locknuts ( D ) tab... Tighten it up too much for now ) through opening under discharge as... To put together on the outside of the mower deck ( A ) 44-inch front blade in bracket H-frame... Back of the mower two 16mm clevis pins ( E ) behind bracket. And spring locking pin ( T ) through metal loop ( D ) P ) total weight the... Systems available in the service section of your bagger operator ’ s Manual came unassembled took. Series snow john deere 300 series bagger installation installation, always secure receiver to brackets with four M10 x 25 (! Under upper chute ( A ) through opening in hopper case tab on mower deck discharge opening C! Series John Deere bagger chute Attaching strap kit - M67099KIT ( 27 ) $ 13.11 easy-to-empty. ) with H-frame ( G ) under retainer ( A ) between stop bracket and mounting bracket both! Gt or GX tractor and X300 Series Weather Enclosure - LP55438-John Deere X300 attachments mounting strap D! In 2013 the gage wheel bracket and mounting bracket with top holes in support frame ( A ) into chute... Flat washers ( G ) onto rod end and secure with washers ( C and... Side of discharge opening, and that bagger pin ( T ) hole...